Benq MP611c Bedienungsanleitung Seite 1

WelcomeMP611/MP611c Digital ProjectorMainstream SeriesUser Manual

Introduction6Shipping contentsThe projector is shipped with the cables required for connection to a PC or video equipment. Carefully unpack and verify

Introduction 7Projector exterior viewFront/upper sideRear sideSee "Connection" on page 17 for details. Lower side view1. External control pa

Introduction8Controls and functionsProjector1. Power (Refer to "Start up" on page 23 and "Shutting down the projector" on page 34

Introduction 912. 5ExitExits and saves the menu settings.When the on-screen menu is activated, the #9 to #12 buttons are used as directional arrows to

Introduction10Remote control1. Power (Refer to "Start up" on page 23 and "Shutting down the projector" on page 34 for more informa

Introduction 11Remote control effective rangeInfra-Red (IR) remote control sensors are located on the front and the back of the projector. The remote

Positioning your projector12Positioning your projectorChoosing a locationYour projector is designed to be installed in one of four possible installati

Positioning your projector 13Safety instructions for ceiling mounting of the projectorWe want you to have a pleasant experience using your BenQ projec

Positioning your projector14Obtaining a preferred projected image sizeThe distance from the projector lens to the screen, the zoom setting, and the vi

Positioning your projector 15How to determine the position of the projector for a given screen size1. Select your screen size.2. Refer to the table an

CopyrightCopyright 2006 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a

Positioning your projector16There is 3% tolerance among these numbers due to optical component variations. BenQ recommends that if you intend to perma

Connection 17ConnectionWhen connecting a signal source to the projector, be sure to:1. Turn all equipment off before making any connections.2. Use the

Connection18Connecting a monitorIf you want to view your presentation close-up on a monitor as well as on the screen, you can connect the RGB signal o

Connection 19Connecting Video source devicesYou can connect your projector to various Video source devices that provide any one of the following outpu

Connection20Connecting a Component Video source deviceExamine your Video source device to determine if it has a set of unused Component Video output s

Connection 21Connecting an S-Video source deviceExamine your Video source device to determine if it has an unused S-Video output socket available: • I

Connection22Connecting a composite Video source deviceExamine your Video source device to determine if it has a set of unused composite Video output s

Operation 23OperationStart up1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check th

Operation24Utilizing the password functionFor security purposes and to help prevent unauthorized use, the projector includes an option for setting up

Operation 25If you forget the passwordYou will be asked to enter the four digit password every time you turn on the projector. If you enter the wrong

Table of contents iiiTable of contentsImportant safety instructions... 1Introduction ...

Operation26Switching input signalThe projector can be connected to multiple devices at the same time. However, it can only display one at a time. When

Operation 27Auto-adjusting the imageIn some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote con

Operation28For example, Selecting the aspect ratioThe 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and

Operation 29Selecting a picture modeThe projector is preset with several predefined application modes so that you can choose one to suit your operatin

Operation30Hiding the imageIn order to draw the audience’s full attention to the presenter, you can use BLANK to hide the screen image. Press any key

Operation 314. To execute MyScreen utility:i. After MyScreen Wizard is successfully installed, execute MyScreen utility by selecting this icon from

Operation32• Do not unplug the RS232 cable or close MyScreen Wizard window while downloading image. Failing to do so will lead to immediate shutdown o

Operation 33Setting the presentation timerPresentation timer can indicate the remaining presentation time on the screen to help you achieve better tim

Operation34Utilizing FAQ functionPress and hold BLANK/Q? on the projector for 3 seconds or go to Advanced > FAQ. Possible solutions to problems en

Operation 35Menu operationMenu systemPlease note that the on-screen display (OSD) menus vary according to the signal type selected.*When a Video or S-

Table of contentsivTroubleshooting... 51Specifications...

Operation36Using the menusThe projector is equipped with on-screen display (OSD) menus for making various adjustments and settings.There are 17 differ

Operation 37Picture menuSome picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown on th

Operation38Color (depends on the selected input source)Increases or decreases the color intensity of the image.Tint (50)Adjusts the color tones of the

Operation 39Pro-Picture menuSome picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown o

Operation40Setting menu FUNCTION (default setting / value)DESCRIPTIONMute (off)Toggles projector audio and Power On/Off Tone between on and off. To d

Operation 41Advanced menuFUNCTION (default setting / value)DESCRIPTIONMirror (Floor front)The projector can be installed on a ceiling or behind a scre

Operation42High Altitude Mode (off)A mode for operation in areas like high altitude or high temperature. We recommend you use the High Altitude Mode w

Operation 43Information menuThis menu shows you the current operating status of the projector.Some picture adjustments are available only when certain

Maintenance44MaintenanceCare of the projectorYour projector needs little maintenance. The only thing you need to do on a regular basis is to keep the

Maintenance 45Lamp informationCalculation of lamp hourWhen the projector is in operation, the duration (in hours) of lamp usage is automatically calcu

Important safety instructions 1Important safety instructionsYour BenQ projector is designed and tested to meet the latest standards for safety of info

Maintenance46Replacing the lamp• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing t

Maintenance 473. Remove the lamp cover from the projector.Do not turn the power on with the lamp cover removed.4. Remove the lamp cords from the slots

Maintenance4814. Restart the projector.Do not turn the power on with the lamp cover removed. 15. Resetting the lamp counter Do not reset if the lamp i

Maintenance 49IndicatorsIllustration• Blank -: Light OFF•O: Orange light•: Light flashing• R: Red light•: Light ON• G: Green lightLight Status & D

Maintenance50Light Status & DescriptionPower Temp LampThermal events--The projector has shutdown automatically. If you try to re-start the project

Troubleshooting 51TroubleshootingTHE PROJECTOR DOES NOT TURN ON.NO PICTUREBLURRED IMAGEREMOTE CONTROL DOES NOT WORKTHE PASSWORD IS INCORRECTCause Reme

Specifications52SpecificationsProjector specifications All specifications are subject to change without notice. GeneralProduct name Digital ProjectorM

Specifications 53Timing chartSupported timing for PC inputSupported timing for Component-YPbPr inputSupported timing for Video and S-Video inputsResol

Specifications54Dimensions278 mm (W) x 94 mm (H) x 219.5 mm (D)Unit: mm 219.52789464.353

Warranty 55WarrantyLimited warrantyBenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof o

Important safety instructions2 Safety Instructions (Continued)7. The lamp becomes extremely hot during operation. Allow the projector to cool for app

Regulation statements56Regulation statementsFCC statementCLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not in

Important safety instructions 3 Safety Instructions (Continued)12. Do not place this projector in any of the following environments. - Space tha

Important safety instructions4Safety Instructions (Continued)16. Do not step on the projector or place any objects upon it. Besides probable physical

Introduction 5IntroductionProjector featuresThe projector integrates high-performance optical engine projection and a user-friendly design to deliver